CPS Series

Coaxial Point Source

The CPS (Coaxial Point Source) Series is our brand new high power, point source system.

There are five full range cabinets available, two of them ultra-compact passive cabinets, together with one sub-bass unit, CPS-18S. Extreme care has been taken to select and customize the most advanced components on the market, including coaxial Mid/high drivers together with full electronic synergy through the coupling of the system amplification & integrated DSP technology.

Total system control is also achieved through our 3D prediction software (Rainbow 3D) working together with our remote system management platform (OCS). These cutting edge softwares together with the CPS technology provides the most optimum and precise listening experience to every ear in the audience.

N

Perfectly suited for:

→  Outdoor events

→  Large stadiums / arenas

→  Houses of worship

→  Theatres

→  Auditoriums

→  Clubs

I

Self Powered

Both CPS cabinets include class D amplification, with switching power supply. The integrated amplification far exceeds the transducers’ needs thus resulting in high output, high damping factor and extremely low levels of distortion.

They are also equipped with energy saving PFC (Power Factor Correction). The power supply regulates itself when AC mains change, so the amp power output will not change with mains swinging. It reduces the current draw in 40% approximately.

Digital Processing

Both models have a DSP integrated into each cabinet. This DSP, with double precision filters, 64bit internal processing and double dynamics (RMS & Peak) optimizes all the system components and electronics, providing maximum system efficiency and total protection whilst significantly and noticeably lowering distortion.

Click here to go to the DSP module configuration

Online Control

Online system (Ethernet or PC) to control each cabinet in real time.

2 x 14″ + 1 x 2″ dual diaphragm coaxial driver, 6000W Class D

Active / passive available

2 x 10″ + 1 x 1.4″ coaxial driver, 3000W Class D

Active / passive available

1 x 14″ + 1 x 1.4″ coaxial driver, 3000W Class D

Active / passive available

CPS-18S-mini1 x 18″ 3000W Class D, 132 dB

Active / passive available

1 x 5″ coaxial, 150 W 

1 x 4″ coaxial, 100 W 

 DSP configuration

DSP module configuration panel

On the back pannel of the cabinet you will find the digital control area. From the compact joystick located below the screen you are able to configure the basic adjustment functions of the internal DSP.

Just move the joystick to select the icons on the left of the screen. You can enter into the following functions: Home, settings, folder, configuration and information. Please note that you must apply the desired configuration in each one cabinet and requires electrical power to work.

If changes are not made the display will automatically dim to avoid unnecessary light in situations where light is not wanted. To re-activate the light simply press the joystick.

The following screens are an example and may vary slightly for each cabinet.

Configuration panel:

HOME

On the main screen you can see the cabinet’s input and output:

Input: You can see a vumeter with the input level and a clip signal.

Output: You have a vumeter with the output level (0 dBu is the amp’s maximum level) You can check the compressor and control the dynamic activity.

SETTINGS

This panel allows you to change the gain, polarity, mute and the delay for the inputs.

You also have the possibility of putting a high pass, changing the type of filter, frequency and order.

FOLDER

The folder screen shows you the name of the preset and its description.

Using the joystick you can change the preset.

CONFIGURATION

This screen is to configurate Ethernet. You can choose automatic or manual.

You can also configure the screen saver.

And here you have the input selection. You can choose between analog or AES3 for channel 1 or channel 2.

INFORMATION

The last screen shows you some general information regarding the cabinet’s components.

Here you can see the cabinet model, its serial number, DSP firmware and hardware versions, amp module model with hardware version, as well as the accelerometer status.

 

Watch the following TUTORIAL to understand how it works:

DSP module configuration panel

On the back panel of the cabinet you will find the digital control area. From the compact joystick located below the screen you are able to configure the Basic adjustment functions of the internal DSP.

Just move the joystick to select the icons on the left of the screen. You can enter into the following functions: Home, settings, folder, configuration and information. Please note that you must apply the desired configuration in each one cabinet and requires electrical power to work.

If changes are not made the display will automatically dim to avoid unnecessary light in situations where light is not wanted. To re-activate the light simply press the joystick.

The following screens are an example and may vary slightly for each cabinet.

HOME

On the main screen you can see the cabinet’s input and output.

Input: You can see a vumeter with the input level and a clip signal.

Output: You have a vumeter with the output level (0 dBu is the amp’s maximum level) You can check the compressor and control the dynamic activity.

SETTINGS

This panel allows you to change the gain, polarity, mute and the delay for the inputs.

You also have the possibility of putting a high pass, changing the type of filter, frequency and order.

FOLDER:

The folder screen shows you the name of the preset and its description.

Using the joystick you can change the preset.

CONFIGURATION:

This screen is to configurate Ethernet. You can choose automatic or manual. You can also configure the screen saver.

And here you have the input selection. You can choose between analog or AES3 for channel 1 or channel 2.

INFORMATION:

The last screen shows you some general information regarding the cabinet’s components.

Here you can see the cabinet model, its serial number, DSP firmware and hardware versions, amp module model with hardware version, as well as the accelerometer status.

Watch the following TUTORIAL to understand how it works:

Descarga nuestra Guía para expertos:

Cómo posicionar tus subgraves para conseguir los mejores resultados

Con esta sencilla Guía gratuita aprenderás lo siguiente:

✓ Cómo evitar lóbulos de presión y efectos pasillo con cancelaciones no deseadas

✓ Ventajas de las configuraciones en línea y el arco electrónico

✓ Detalles técnicos y fórmulas que te ayudarán a elegir la mejor opción en cada evento

Consentimiento para recibir la newsletter

Ya puedes descargar la guía