LX F6

 
Ultra-compact Self-powered (Class D switch mode power supply) front loaded, three-way Line Array, dual 6″ neodymium transducers with nomex cones and one HF Air Motion Transformer with kapton diaphragm.
DSP (FIR technology) controlled with 1500W amplification , 127db SPL, built-in inclinometer. A passive version of this cabinet is also available for ‘slave link’.

 

Specifications 
Components

LF/MF: Dual 6” custom Nomex cones + Neodymium magnets

HF: Air Motion Transformer system, AMT driver with kapton diaphragm

Frequency Range 75Hz – 20KHz
Frequency Response 90Hz – 18KHz ± 3dB
Max. SPL 124 dB / 127 dB peak
Coverage Angle 100º H x V according to configuration.
Power 1500 W Class D switching power supply
LF/MF Amplifier 1 x 750 W
HF Amplifier 1 x 750 W
Processing 56 bit Lynx dspb-22 with FIR filters
Control Cabinet angle detection – temperature sensor – Fan speed – Online Control
Control Connections Ethernet (OCS) optional / USB (DSP programming)
AC Power 230V / 115V selectable. 50/60 Hz 5A
AC Connections 16A Neutrik Powercon with link output
Finish Polyurea coating – white colour optional (RAL)
Material Premium birch plywood
Dimensions 204 x 644 x 290 mm (H x W x D) without pins
Weight 23 Kg (50 lbs) /Passive 20Kg (44 lbs)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The LX-F6 is part of the Lynx Line Array Series. Line Array topology is employed to create cylindrical radiation, increasing throw and achieving a precise control of both horizontal and vertical dispersion. The LX-F6 is the ideal solution for application in theatres, concert halls, stadiums, auditoriums, conference halls or any event where high precision Line Array is required.
 
The LX-F6 is a high output three-way, front loaded self-powered cabinet. For the low-mid frequencies it uses dual 6” neodymium transducers with nomex cones and suspension. The high frequencies are looked after by a 1” x 5” AMT (Air Motion Transformer). The advantage of this type of device consists in the small and very controlled movement of each fold, accelerating the surrounding air inside each fold producing an almost perfect acoustical output in amplitude, phase and all the radiating areas of the transducer. This creates unbeatable transient response, far superior to both conventional drivers and ribbon drivers. The result is crystal clear vocals. The system is powered with a total of 1500W of class D amplification, 1000W for the low/mid frequencies and 500W for the high frequencies. Each cabinet has a DSP integrated which applies linear phase (FIR) and classical crossover. Other features include temperature sensor, fan speed control, inclinometer, Ethernet options and many more.
 
The LX-F6 has a selection of rugged hardware available. The SV-LXF6 flying frame can hold up to 36 cabinets with splay angles selectable in 0.5º increments between 0º to 3º and 1º increments between 3º to 12º. Sub bass cabinet LX-212S can also be flown in array with the LX-F6 with the SVLX212 flying frame. The FC-LXF6 flight case can house up to 4 cabinets and the FC-LX212/6 flight case houses one LX-212S sub-bass and 4 LX-F6. Rain hoods are also optional to protect the system electronics. A passive version of the cabinet, the LX-F6P is also available.
This cabinet can be linked to and powered by the LX-F6 creating a more economical Line Array whilst maintaining the same power as a fully powered line array configuration.
 
With a very high power to size ratio and with easy rigging options offered the system can be taken from the truck and rigged up in record time. It is also very easy to use and control without the need for any external amps. To extend the low frequency response, the LX-212S or the LX-218S sub bass cabinets can be used.
Trasera LX-F6 
 
Bi-amplified Class D with switching power supply. Includes one 1000W power modules, for the 6” transducers and one 500W power module for the High Frequency AMT.
 
The amplification far exceeds the transducers needs thus resulting in high output, high damping factor and extremely low levels of distortion.
 
 
 

Lynx-Inclinometer_logo

DSP-Grey

Lynx ocs-icon

 

 

The cabinets offer built in Inclinometer, Digital Signal Processor integrated and Online Control System

Check more details

Click Here

Components LX-F6

 

Speaker-lx-f6

For the low-mid frequencies it uses dual 6” neodymium transducers with neodymium magnet groups, nomex cones and suspension with weather protected membrane for outdoor use and ventilated voice coil for improved heat dissipation.

 

LX-F6 TPL-150

The high frequencies are looked after by an Air Motion Transformer driver TPL-150, which is a very special tweeter with folded diaphragm. The advantage of this type of device consists in the small and very controlled movement of each fold, accelerating the surrounding air inside each fold producing an almost perfect acoustical output in amplitude, phase and all the radiating areas of the transducer. This creates unbeatable transient response, far superior to both conventional drivers and ribbon drivers. The result is crystal clear vocals.  You will find more info about this special driver TPL-150 here.

 

 

 

 

 

 

Accessories

 

BALL-PSR
BALL-PSR0820R
Ball pin with thread for LX-F6 / LX-F6P cabinets
SV-LXF6
SV-LXF6
Flying frame for the LX-F6 and LX-F6P, with a capacity for rigging of up to 36 cabinets
SS-LXF6
SS-LXF6
Ground stack support for LX-F6 and LX-F6P
SA-LX215
ST-212
Accessory to stack LX-F6 or LX-F6P on sub LX-212S with inclination of 0º / 3º / 6º / 9º
FA-F6
SA-F6
Accessory for negative angulation
SA-212
SA-212
Adaptor used to fly the LX-F6 under the sub units LX-212S
SP-TLF61
SP-TLF6
Adjustable T-Bar support for LX-F6 with LX-212S. Pole is included
Rain-Cover
FD-1LXF6NL
Rain cover for the back panel of the LX-F6
FC-LXF6
FC-LX212/F6
Flight case for 4  LX-F6 / F6P with 1 sub LX-212S
FC-LXF6
Flight case for 4 x LX-F6 / F6P

 

 

Hardware LX-F6 

 

Enclousure-v12

 
Enclosure

The LX-F6 cabinet is constructed from 11-ply premium birch plywood (15mm thickness) and finished with high-resistant water based black paint.

Internal-design-f6

 
Internal design

The internal structure of the LX-F6 is heavily braced for greater longevity and all parts are assembled on metal inserts with metric screws. The amplification modules & DSP are housed in a separate chamber to the drivers avoiding excessive heat & vibration, thus delivering greater efficiency and reliability.

Rearpanel-f6

 
Rear panel

The powder coated steel rear panel contains all connections and houses the LX-F6s amplification modules and DSP, is easily accessible and housed separately from the drivers for increased reliability and efficiency.

Grill-f6

 
 Grill

The LX-F6 has a heavy duty, powder coated front grille with a special acoustic rear fabric to protect the transducers against dust and dirt

Handle-f6

 
Handles

Handles are integrated in to the side plates of the LX-F6 to facilitate transport, positioning and loading of the cabinets.

rigging-f6

 
Rigging

Integrated flying plates are located on each side of the enclosure, to link LX-F6 cabinets together with optional splay angles, from between 0° to 3° with 0.5° step increments and from between 3º to 9º with 1º increments to create the desired curve.

Transport-f6

 
Transport

Two durable flight cases are available. Either for 4 cabinets of LX-F6 alone or for 4 cabinets of LX-F6 and one LX-212S together. The flight cases both come with space allocated for cabling.

 

 

 

Phase Response 

 

P.Response-LX-F6

 

Polars

 

100Hz

Polar-LX-F6_100Hz

250Hz

Polar-LX-F6_250Hz

400Hz

LX-F6@400Hz

630Hz

LX-F6@630Hz

1250Hz

Polar-LX-F6_1250Hz

2000Hz

Polar-LX-F6_2000Hz

4000Hz

Polar-LX-F6_4000Hz

6300Hz

Polar-LX-F6_6300Hz

8000Hz

Polar-LX-F6_8000Hz

10000Hz

Polar-LX-F6_10000Hz

12500Hz

Polar-LX-F6_12500Hz

16000Hz

LX-F6@16000Hz

 

 

 

Dimensions

LYNX_LX-F6-measures

Other products from this serie

LX-V12 product2 x 12” and 4 x 6.5” transducers with 2 x 1.4” drivers, 143 dB SPL

LX-318C product3 x 18” transducers (2 Frontal + 1 Rear), 141 dB SPL

LX-V8 product2 x 8” transducers with 2 x 1” drivers, 134 dB SPL

LX-218S product2 x 18” transducers, offering 139 dB SPL

LX-212S product2 x 12” transducers, offering 139 dB SPL

/* Estilos para menú plegable móvil Divi */ /* JS para menú plegable móvil Divi */