CPS-214
DSP integrated coaxial point source
Extremely compact & powerful 3-way, self-powered (6000 W Class-D with PFC), DSP integrated coaxial point source element. Dual high power 14″ neodymium transducers and a unique 2″ Exit throat (HF 1.75″ voice coil/ MF 3.5″ voice coil) coaxial neodymium compression driver.
Description
The CPS-214 is a high-output extremely compact and extremely powerful 3-way, self-powered, DSP integrated, symmetrical Coaxial Point Source element designed for large sized touring & fixed installations.
It uses two low distortion 14″ (4″ DUO double layer voice coil) custom speakers for the low frequencies with exclusive Malt Cross cooling technology, FEA optimized neodymium magnet circuit, aluminium demodulating ring and weatherproof cone.
For the mid/high frequencies it uses an ultra light weight 2″ exit throat dual diaphragm coaxial compression driver. The unique voice coil technology employs a light weight copper clad aluminium wire, wound inside and out of the Kapton former to improve heat dissipation, dramatically increasing the acoustic output and reliability of the driver while minimizes the power compression.
The larger annular midrange diaphragm covers the frequency range between 300Hz and 7KHz with a smooth, linear response. The ultra light annular diaphragm for the high frequencies offers exceptional transient response with very high efficiency from 6KHz to 22Khz. With two subsystems in one each driver covers a smaller frequency range for increased power handling, high dynamic and extremely low distortion and delivers excellent phase coherence & perfect time alignment without problems of multi-source interference.
The 6000W 2 channel Class-D amplifier with PFC (Power Factor Correction) offers exceptional efficiency with maximum system performance whilst significantly lowering power consumption. With Thermal, short-circuit and overload protections the system module delivers superior sonic performance. Coupled together with our new generation, 64 bit/96KHz processor the system electronics are yet further guaranteed not only the utmost protection but the best performance.
Designed in-house by Lynx Pro Audio engineers our DSP offers the most recent advances in digital processing such as FIR filters delivering a linear phase & frequency response. The latest 32 bit/96KHZ AD/DA converters make the system one of the most advanced & innovative point source systems on the market resulting in pristine sound quality.
A 2.8″ IPS user interface is located on the enclosure’s back panel and has multifunction joystick control enabling the user to control, select and/or adjust parameters such as cabinet presets, gain, delay and input EQ (see user manual). Two Ethernet ports enable the system to be controlled with the OCS platform for easier alignment, monitoring and processing of the cabinet together with the new Rainbow 3D prediction software delivers a complete system design tool.
The enclosure is made from premium grade birch plywood and finished with a polyurea coating for longer durability & weather protection.
Perfectly suited for:
| → Live events | |
| → Large stadiums / arenas | |
| → Auditoriums | |
| → Houses of worship | |
| → Theatres | |
| → Clubs |
Key features
|
→ Extraordinary power-to-size ratio |
|
→ Unique 2” dual diaphragm compression driver |
|
→ Integrated Digital processor (64 bit / 96 KHz) with FIR linear phase filtering |
|
→ FIR linear phase filtering |
|
→ Ergonomic design in premium birch plywood & finished in polyurea |
|
→ 2.8” IPS display with multifunction joystick control |
Technical Data
Components |
LF: 2 x 14” (4” voice coil), neodymium magnet, 2000 W (AES). |
MF: 3.5” (90mm) voice coil, 150W (AES).HF: 1.5” (44,4 mm) voice coil, 80W (AES) |
|
| Frequency Range |
55 Hz – 22 KHz (-6dB) |
Coverage |
Rotatable 60ºH x 40ºV |
| Max SPL |
Low: 137 dB / 143 dB Mid/ High: 139.5 dB / 142.6 dB |
Power amplifier |
6000 W Class D with switching power supply & PFC
|
| Processing |
Internal Lynx Processor DSPB-FL. |
Crossover |
Digital: FIR filter 550 Hz / Passive: 6.3 KHz |
| Control | User control interface with 2.8” IPS screen and multifunction joystick controller |
Control connections |
USB (DSP programming) / Dual Ethernet port |
| Input |
BAL/UNBAL XLR connectors analog input AES/EBU digital input optional |
Nominal voltage |
100 – 240V AC @ 50-60 Hz |
| Operating voltage | 85 – 264V AC |
AC Connectors |
16A Neutrik powerCON TRUE1 TOP with looping output |
| Finish | Polyurea coating, high grade resistant paint |
Material |
15 mm premium birch plywood |
| Dimensions | 900 x 420 x 515 mm (H x W x D) |
Weight |
49 Kg (108 lbs) |
DSP configuration
DSP configurationDSP module configuration panel
On the back pannel of the cabinet you will find the digital control area. From the compact joystick located below the screen you are able to configure the basic adjustment functions of the internal DSP.
Just move the joystick to select the icons on the left of the screen. You can enter into the following functions: Home, settings, folder, configuration and information. Please note that you must apply the desired configuration in each one cabinet and requires electrical power to work.
If changes are not made the display will automatically dim to avoid unnecessary light in situations where light is not wanted. To re-activate the light simply press the joystick.
The following screens are an example and may vary slightly for each cabinet.
Configuration panel:
 |
HOME On the main screen you can see the cabinet’s input and output: • Input: You can see a vumeter with the input level and a clip signal. • Output: You have a vumeter with the output level (0 dBu is the amp’s maximum level) You can check the compressor and control the dynamic activity. |
 |
SETTINGS This panel allows you to change the gain, polarity, mute and the delay for the inputs. You also have the possibility of putting a high pass, changing the type of filter, frequency and order.
|
 |
FOLDER The folder screen shows you the name of the preset and its description. Using the joystick you can change the preset. |
 |
CONFIGURATION This screen is to configurate Ethernet. You can choose automatic or manual. You can also configure the screen saver. And here you have the input selection. You can choose between analog or AES3 for channel 1 or channel 2. |
 |
INFORMATION The last screen shows you some general information regarding the cabinet’s components. Here you can see the cabinet model, its serial number, DSP firmware and hardware versions, amp module model with hardware version, as well as the accelerometer status. |
Watch the following TUTORIAL to understand how it works:
DSP module configuration panel
On the back panel of the cabinet you will find the digital control area. From the compact joystick located below the screen you are able to configure the Basic adjustment functions of the internal DSP.
Just move the joystick to select the icons on the left of the screen. You can enter into the following functions: Home, settings, folder, configuration and information. Please note that you must apply the desired configuration in each one cabinet and requires electrical power to work.
If changes are not made the display will automatically dim to avoid unnecessary light in situations where light is not wanted. To re-activate the light simply press the joystick.
The following screens are an example and may vary slightly for each cabinet.
HOME
On the main screen you can see the cabinet’s input and output.
• Input: You can see a vumeter with the input level and a clip signal.
• Output: You have a vumeter with the output level (0 dBu is the amp’s maximum level) You can check the compressor and control the dynamic activity.
SETTINGS
This panel allows you to change the gain, polarity, mute and the delay for the inputs.
You also have the possibility of putting a high pass, changing the type of filter, frequency and order.
FOLDER:
The folder screen shows you the name of the preset and its description.
Using the joystick you can change the preset.
CONFIGURATION:
This screen is to configurate Ethernet. You can choose automatic or manual. You can also configure the screen saver.
And here you have the input selection. You can choose between analog or AES3 for channel 1 or channel 2.
INFORMATION:
The last screen shows you some general information regarding the cabinet’s components.
Here you can see the cabinet model, its serial number, DSP firmware and hardware versions, amp module model with hardware version, as well as the accelerometer status.
Watch the following TUTORIAL to understand how it works:
More features
Hardware for CPS-214
 |
EnclosureThe CPS-214 cabinet is constructed from 11-ply premium birch plywood (15mm thickness) and finished with polyurea coating |
 |
Internal designThe internal structure of the CPS-214 is heavily braced for greater longevity and all parts are assembled on metal inserts with metric screws. The amplification modules & DSP are housed in a separate chamber to the drivers avoiding excessive heat & vibration, thus delivering greater efficiency and reliability. |
 |
Rear panelThe powder coated steel rear panel contains all connections and houses the CPS-214 amplification modules and DSP, is easily accessible and housed separately from the drivers for increased reliability and efficiency |
 |
GrillThe CPS-214 has three heavy duty, powder coated front grille with a special acoustic rear fabric to protect the transducers against dust and dirt. |
 |
HandlesThe CPS-214 has six ergonomic handles with firm internal grip to facilitate transport, positioning and loading of the cabinets. Two handles are placed at the top and bottom of the cabinet and four handles are located on the sides. |
 |
RiggingFour heavy duty track are integrated on each side (top and bottom) of the enclosure to facilitate its installation. |
 |
TransportThe CPS-214 is easy to transport thanks to its dedicated Dolly. The cabinets lock in 2 points on to the dolly and a protective nylon cover is also available to protect the enclosure and keep it clean on tour. |
Rear image
Accessories for CPS-214
 |
AGR-10 |
 |
SC-FC1 |
 |
UBR-HCPS214 Horizontal U bracket for CPS-214 |
 |
UBR-VCPS214
Vertical U bracket for CPS-214
|
 |
CA-CPS214 Removable front transport dolly for CPS-214 |
 |
SV-CPS214 Flying frame for CPS-214
|
 |
FD-1CPS214NL Rain cover for CPS-214 |
 |
FD-CPS214 Nylon protection for CPS-214 |
Install version
CPS-214IN
The CPS-214IN is the install version of the CPS-214 cabinet. This version is specially designed for fixed installations.
The Installation version is available in active/passive version. It has a ferrite driver, it doesn’t have handles and is the only version available in RAL colour on demand.
CPS-214IN
The CPS-214IN is the install version of the CPS-214 cabinet. This version is specially designed for fixed installations.
The Installation version is available in active/passive version. It has a ferrite driver, it doesn’t have handles and is the only version available in RAL colour on demand.
Downloads
