HPX Series

Amplifiers

New generation of professional touring amplifiers offering from 4600 to 12000 watts.

The HPX series feature four channel models, ready for rough handling in the touring world.

They are at the forefront of audio design, offering a powerful, reliable and lightweight amplifier designed to deliver superior sound quality for your touring gigs.

Technical Data

 

HPX-6400

HPX-12000

[DSP available]

 Output Power
 @ 2 Ohms 4 x 3025 W  – –
 @ 4 Ohms 4 x 1600 W 4 X 2950 w
 @ 8 Ohms 4 x 820 W 4 x 1550 W
 Bridge @ 4 Ohms 2 x 6050 W  – –
 Bridge @ 8 Ohms 2 x 3200 W 2 x 5900 W
High Impedance
70V rms / 100V peak  – –  – –
100V rms / 140V peak  – –4 x 2950 W
 Frequency Response 
 Power Bandwidth ± 0.25 dB 20Hz-20KHz 20Hz-20KHz
 Phase Response 
 @ 1 W 20Hz-20KHz ±15 deg ±15 deg
 Total Harmonic Distortion   
 20Hz-20KHz <0.05% <0.05%
 Intermodulation Distortion   
 SMPTE <0.05% <0.05%
 Damping Factor  
 20-500Hz @ 8 Ohms  >500  >500
 Crosstalk   
 20Hz-1KHz >80 dB >80 dB
 Voltage Gain    
 0.5 dB steps 26 dB to 38 dB 26 dB to 38 dB
 Sensitivity    
 Rated Power (26/32/38 dB Gain) 4.1/2/1 V 5.6/2.8/1.4 V
 Signal to Noise Ratio 
 20HZ-20KHz 113 dB 116 dB
 Required AC Mains 
 Operating Voltage (50Hz-60Hz) 170V-265V AC 170V-265V AC
 Power on Idling (@230V) 0.5 A 0.5 A
 1/8 Rated Power (@230V min.Z)  14 A 13 A
 Dimensions
 W x H x D (mm) 483 x 89 x 460 483 x 89 x 460
 W x H x D (inches) 19 x 3.5 x 18.1 19 x 3.5 x 18.1
 Weight    
 Net 12 Kg / 26.5 lbs 12 Kg / 26.5 lbs
 Protections   
 Soft-start, Turn-on Turn-off transients, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, ICL™, PMS™ and SSP™. DSP available.

More features

DSP features

• AD Converters: Advanced multibit Delta-Sigma architecture, 24 Bit, 120dB Dynamic Range, 0.00032%THD+N

• DA Converters: Advanced multibit Delta-Sigma architecture, 24 Bit, 120 dB Dynamic Range, 0.00045% THD+N

• AES3 Input: 140dB Dynamic Range, 0.0001% THD+N, Sample Rate Converter (16 to 24 bit, 44.1kHz to 192kHz)

• Maximum Input/Output: +20dBu

• DSPs internal process: 56-bit double-precision floating-point

• Latency analog input: 0.6ms (2.67ms with FIR process)

• Equalizer: Custom FIR and IIR: Parametric (Q Adaptative or Constant), Shelving (Low/High, 6dB/12dB, Q variable), Butterworth (Low/High Pass), Low/High Pass (Q Variable), Band Pass, Stop Band, All pass (Q Variable)

• Crossover: Linear Phase FIR (Low/High pass, Band Pass and Custom) , Hybrid FIR-IIR, Butterworth/Linkwitz-Riley/Bessel IIR (6dB/oct to 48dB/oct)

• Delay: 4x 341.25ms (118m) Input and 4x 52.08ms (18m)

• Output Limiters: RMS and Peak Power (Ratio, Knee, Attack, Hold and Release times variable)

Available options

• Standard Signal Inputs Module: The HPX Series amps are equipped as standard with a Neutrik® XLR input doubled by other XLR connectors for linking purpose, per channel

DSP HPXThe HPX Series Digital Signal Processor is real time fully programmable through Ethernet, USB or directly from the front panel. There are two different versions: 4 Inputs/4 Outputs or 2 Inputs/2 Outputs totally free route configurable. Both versions include post-processor signal XLR output connectors to link the processed signal to another amplifier without DSP.

•Domain Manager™ Networking  AES67 Audio Input: 4 inputs channels  can be installed in the HPX Series equipped with DSP. Sampling frequency can be configured as 48, 96 or 192 kHz. Audio format is Audio Networking AES67 over IP and AES67 RTP. Two RJ45 connectors are configurable as 1 GHz/100 MHz for Primary/Secondary network, or standard switch.

• AES3 Input: Provides standard AES3 (AES/EBU) digital input using two input XLR connector in 4 channels models or one XLR connector in 2 channels models. It include a high performances sample rate converter to adapt any signal. You can select Digital/Analog input using the front panel Menu, where you can configure also the termination resistor.

• Ethernet LAN Port: standard RJ45 connector for Ethernet network connection. Using it you can control/monitor the amplifier and the DSP.

• GPIO module for HPX Series: This General Purpose Input Output (GPIO) module, permits monitoring the amplifier ON/OFF status (GENERAL PURPOSE OUTPUT) to control an external device by an internal relay.

GENERAL PURPOSE OUT connector provides some contacts to monitoring the status. Contacts marked as OK will remain short-circuited when amp is correctly working and will be opened if the amplifier is in standby mode.

Other amplifiers

High Power

2 & 4 Channel

Multipurpose

Featured references

Akuarela Beach, one of the most popular venues during summer

Akuarela Playa opens every summer in the city of Valencia (Spain) to make the evenings more special. This club, which is located in front of Malvarrosa’s beach…

Read more

Seo-gu Healing Art Festival in Daejeon, South Korea

Seo-gu Healing Art Festival is held during three days in May in Daejeon, South Korea. It has a huge stage for the many shows that take place during the festival…

Read more

Lynx Pro Audio at the Shanghai International Arts Festival

On October 2019, Lynx Pro Audio sound equipment was installed at the 21st edition of the International Art Festival of Shanghai “Arts Bird” and…

Read more

Professional sound for the Beer Festival in Paysandú

Beer Festival is celebrated since 1996 in the city of Paysandú, Uruguay. This festival is one of the most famous events in the country, takes place during…

Read more

Descarga nuestra Guía para expertos:

Cómo posicionar tus subgraves para conseguir los mejores resultados

Con esta sencilla Guía gratuita aprenderás lo siguiente:

✓ Cómo evitar lóbulos de presión y efectos pasillo con cancelaciones no deseadas

✓ Ventajas de las configuraciones en línea y el arco electrónico

✓ Detalles técnicos y fórmulas que te ayudarán a elegir la mejor opción en cada evento

Consentimiento para recibir la newsletter

Ya puedes descargar la guía